Are you searching for a technique to increase the safety of your private home? Are you looking out for an clever doorbell that can allow you to keep watch over your entrance door regardless of the place you might be? Chances are you’ll now relaxation straightforward realizing that the Ring Doorbell is the reply to all of your queries. This text will stroll you thru the method of organising your Ring Doorbell step-by-step, guaranteeing that you’ve a stress-free expertise.
Earlier than we begin, be sure you have the next instruments and supplies readily available: a drill, a screwdriver, a degree, a hammer, a pencil, and a tape measure. To put in your Ring Doorbell efficiently, additionally, you will want the next: a Ring Doorbell, a mounting bracket, a doorbell transformer, doorbell wires, and a screwdriver. After getting collected all the obligatory provides, you may start organising your Ring Doorbell.
Armed with the mandatory instruments and supplies, you are now able to dive into the set up course of. Don’t be concerned, we’ll break it down into manageable steps so you may get pleasure from peace of thoughts realizing you have secured your private home’s entry level.
The best way to Set up Ring Doorbell
Earlier than you begin the set up, be sure you collect all the mandatory instruments and supplies, together with the Ring Doorbell, mounting bracket, doorbell transformer, doorbell wires, drill, screwdriver, degree, hammer, pencil, and tape measure.
- Flip off energy to doorbell.
- Take away present doorbell.
- Set up mounting bracket.
- Join doorbell wires.
- Mount Ring Doorbell.
- Degree and safe Ring Doorbell.
- Restore energy to doorbell.
- Take a look at Ring Doorbell.
After getting put in your Ring Doorbell, obtain the Ring app and comply with the on-screen directions to finish the setup course of. You may then use the app to manage your Ring Doorbell and obtain notifications when somebody rings your doorbell or triggers the movement sensor.
Flip off energy to doorbell.
Earlier than you start putting in your Ring Doorbell, it’s important to show off the ability to your present doorbell. It will forestall any electrical shocks and guarantee which you can work safely.
-
Find your doorbell breaker.
That is normally positioned in your house’s electrical panel. The doorbell breaker is usually labeled “Doorbell” or “Chime.”
-
Flip off the doorbell breaker.
After getting discovered the doorbell breaker, flip it to the “Off” place. It will minimize off energy to your doorbell.
-
Take a look at the doorbell.
Press the doorbell button to make it possible for it’s now not working. If the doorbell nonetheless rings, then you haven’t efficiently turned off the ability. Verify the breaker once more and make it possible for it’s within the “Off” place.
-
Take away the duvet out of your doorbell chime.
After getting confirmed that the ability is off, you may take away the duvet out of your doorbell chime. It will expose the doorbell wires.
Now that you’ve turned off the ability to your doorbell, you may safely proceed with the set up of your Ring Doorbell. Bear in mind to at all times comply with the directions offered within the Ring Doorbell consumer guide.
Take away present doorbell.
After getting turned off the ability to your doorbell, you may proceed with eradicating the prevailing doorbell. This course of will fluctuate relying on the kind of doorbell you will have.
-
Take away the doorbell button.
The doorbell button is usually held in place by one or two screws. Use a screwdriver to take away the screws after which gently pry the doorbell button off the wall.
-
Disconnect the doorbell wires.
After getting eliminated the doorbell button, you will note two wires related to the again of the button. These are the doorbell wires. Use a pair of pliers to twist the wire nuts counterclockwise after which pull the wires aside.
-
Take away the doorbell chime.
The doorbell chime is normally positioned inside your private home, close to the entrance door. Take away the duvet from the chime after which disconnect the wires from the chime terminals. As soon as the wires are disconnected, you may take away the chime from the wall.
-
Patch the holes.
After getting eliminated the doorbell button and chime, you’ll be left with two holes in your wall. You may patch these holes with spackling compound or caulk.
Now that you’ve eliminated the prevailing doorbell, you might be prepared to put in your Ring Doorbell. Be sure that to comply with the directions offered within the Ring Doorbell consumer guide.
Set up mounting bracket.
The mounting bracket is what is going to maintain your Ring Doorbell in place. You will need to set up the mounting bracket appropriately, in order that your Ring Doorbell is degree and safe.
-
Select a location for the mounting bracket.
The perfect location for the mounting bracket is subsequent to your entrance door, at a top of about 4 toes from the bottom. Make it possible for the situation you select is degree and that there aren’t any obstructions, reminiscent of bushes or shrubs, that can block the view of the Ring Doorbell.
-
Mark the situation of the mounting holes.
Use a pencil to mark the situation of the 2 mounting holes on the wall. Make it possible for the marks are degree.
-
Drill the mounting holes.
Use a drill to drill two holes on the marks you made within the earlier step. The holes must be deep sufficient to accommodate the anchors that got here with the Ring Doorbell.
-
Insert the anchors.
Insert the anchors into the holes you simply drilled. Faucet the anchors in with a hammer till they’re flush with the wall.
-
Screw the mounting bracket to the wall.
Use the screws that got here with the Ring Doorbell to screw the mounting bracket to the wall. Make it possible for the mounting bracket is degree and safe.
Now that you’ve put in the mounting bracket, you might be prepared to attach the doorbell wires and mount the Ring Doorbell.
Join doorbell wires.
After getting put in the mounting bracket, it’s essential to join the doorbell wires to the Ring Doorbell. The Ring Doorbell has two terminals, labeled “Entrance” and “Rear.” The entrance terminal is for the wire that comes out of your doorbell button, and the rear terminal is for the wire that goes to your doorbell chime.
To attach the doorbell wires, comply with these steps:
-
Strip the ends of the doorbell wires.
Use a wire stripper to take away about 1/2 inch of insulation from the ends of the doorbell wires. -
Twist the ends of the doorbell wires collectively.
Twist the ends of the 2 doorbell wires collectively tightly. -
Insert the twisted wires into the terminals on the Ring Doorbell.
Insert the twisted wires into the “Entrance” and “Rear” terminals on the Ring Doorbell. Make it possible for the wires are inserted all the way in which into the terminals and that they’re making good contact. -
Tighten the terminal screws.
Use a screwdriver to tighten the terminal screws till the doorbell wires are safe.
Now that you’ve related the doorbell wires, you might be able to mount the Ring Doorbell to the mounting bracket.
Be aware: In case you are putting in a Ring Doorbell Professional, additionally, you will want to attach the ability adapter to the Ring Doorbell Professional. The ability adapter plugs into an outlet close to your doorbell.
Mount Ring Doorbell.
Now that you’ve related the doorbell wires, you might be able to mount the Ring Doorbell to the mounting bracket.
-
Align the Ring Doorbell with the mounting bracket.
Place the Ring Doorbell over the mounting bracket in order that the screw holes on the Ring Doorbell line up with the screw holes on the mounting bracket.
-
Insert the screws.
Insert the screws that got here with the Ring Doorbell into the screw holes. Make it possible for the screws are tight and that the Ring Doorbell is safe.
-
Degree the Ring Doorbell.
Use a degree to make it possible for the Ring Doorbell is degree. If the Ring Doorbell will not be degree, loosen the screws and regulate the place of the Ring Doorbell till it’s degree.
-
Tighten the screws.
As soon as the Ring Doorbell is degree, tighten the screws till they’re comfortable.
Now that you’ve mounted the Ring Doorbell, you may restore energy to the doorbell and check the Ring Doorbell.
Degree and safe Ring Doorbell.
After getting mounted the Ring Doorbell to the mounting bracket, you will need to degree and safe it.
-
Use a degree to examine if the Ring Doorbell is degree.
Place a degree on prime of the Ring Doorbell. If the bubble within the degree is centered, then the Ring Doorbell is degree. If the bubble will not be centered, then it’s essential to regulate the place of the Ring Doorbell till it’s degree.
-
Tighten the screws that safe the Ring Doorbell to the mounting bracket.
Use a screwdriver to tighten the screws that safe the Ring Doorbell to the mounting bracket. Make it possible for the screws are tight and that the Ring Doorbell is safe.
-
Apply silicone sealant across the edges of the Ring Doorbell.
It will assist to weatherproof the Ring Doorbell and stop water injury. Use a caulk gun to use a skinny bead of silicone sealant across the edges of the Ring Doorbell.
-
Enable the silicone sealant to dry utterly.
Earlier than you check the Ring Doorbell, enable the silicone sealant to dry utterly. This may increasingly take a number of hours or in a single day.
After getting leveled and secured the Ring Doorbell, you may restore energy to the doorbell and check the Ring Doorbell.
Restore energy to doorbell.
After getting put in the Ring Doorbell and examined it, you may restore energy to the doorbell.
-
Activate the doorbell breaker.
Find the doorbell breaker in your house’s electrical panel. Flip the breaker to the “On” place. It will restore energy to the doorbell.
-
Take a look at the Ring Doorbell.
Press the doorbell button to make it possible for the Ring Doorbell is working correctly. The Ring Doorbell ought to gentle up and you must hear a chime inside your private home.
-
Obtain the Ring app.
If you have not already performed so, obtain the Ring app from the App Retailer or Google Play Retailer. Create an account and comply with the on-screen directions to attach your Ring Doorbell to your Wi-Fi community.
-
Arrange your Ring Doorbell.
As soon as your Ring Doorbell is related to your Wi-Fi community, you should use the Ring app to arrange your Ring Doorbell. This consists of setting your movement detection settings, privateness settings, and notification settings.
Now that you’ve restored energy to the doorbell and arrange your Ring Doorbell, you can begin utilizing it to observe your private home and reply the door from wherever.
Take a look at Ring Doorbell.
After getting restored energy to the doorbell and related it to your Wi-Fi community, you must check the Ring Doorbell to make it possible for it’s working correctly.
-
Press the doorbell button.
The Ring Doorbell ought to gentle up and you must hear a chime inside your private home.
-
Open the Ring app.
In your smartphone, open the Ring app and faucet on the Ring Doorbell that you simply need to check.
-
View the stay video feed.
It is best to now be capable to see a stay video feed from the Ring Doorbell. If you happen to do not see a stay video feed, examine to make it possible for the Ring Doorbell is related to your Wi-Fi community and that the Ring app is updated.
-
Take a look at the movement detection.
Stroll in entrance of the Ring Doorbell and see if the movement sensor is triggered. The Ring Doorbell ought to ship you a notification in your smartphone when the movement sensor is triggered.
In case you are having issues testing your Ring Doorbell, you may contact Ring help for assist.
FAQ
Have extra questions on putting in your Ring Doorbell? Take a look at these incessantly requested questions and solutions.
Query 1: What instruments do I want to put in my Ring Doorbell?
Reply 1: You have to a drill, a screwdriver, a degree, a hammer, a pencil, and a tape measure. Additionally, you will want the Ring Doorbell, a mounting bracket, a doorbell transformer, doorbell wires, and a screwdriver.
Query 2: Do I want to show off the ability to my doorbell earlier than I set up it?
Reply 2: Sure, you must at all times flip off the ability to your doorbell prior to installing it. It will forestall any electrical shocks and guarantee which you can work safely.
Query 3: How do I join the doorbell wires to the Ring Doorbell?
Reply 3: The Ring Doorbell has two terminals, labeled “Entrance” and “Rear.” The entrance terminal is for the wire that comes out of your doorbell button, and the rear terminal is for the wire that goes to your doorbell chime. Twist the ends of the doorbell wires collectively and insert them into the terminals on the Ring Doorbell.
Query 4: How do I mount the Ring Doorbell to the wall?
Reply 4: First, set up the mounting bracket on the wall. Then, align the Ring Doorbell with the mounting bracket and insert the screws. Make it possible for the Ring Doorbell is degree and safe.
Query 5: How do I check my Ring Doorbell?
Reply 5: After getting put in the Ring Doorbell, activate the ability to the doorbell and press the doorbell button. The Ring Doorbell ought to gentle up and you must hear a chime inside your private home. You may as well check the movement detection by strolling in entrance of the Ring Doorbell.
Query 6: What do I do if I am having issues putting in my Ring Doorbell?
Reply 6: In case you are having issues putting in your Ring Doorbell, you may contact Ring help for assist.
Query 7: Can I set up my Ring Doorbell myself?
Reply 7: Sure, you may set up your Ring Doorbell your self. Nonetheless, if you’re not snug working with electrical wiring, it’s possible you’ll need to rent knowledgeable to put in it for you.
Closing Paragraph for FAQ: These are only a few of essentially the most incessantly requested questions on putting in a Ring Doorbell. In case you have another questions, please seek the advice of the Ring Doorbell consumer guide or contact Ring help.
Now that you understand how to put in a Ring Doorbell, listed below are just a few suggestions that can assist you get essentially the most out of your new doorbell.
Ideas
Listed below are just a few suggestions that can assist you get essentially the most out of your new Ring Doorbell:
Tip 1: Select the proper location to your Ring Doorbell.
The perfect location to your Ring Doorbell is subsequent to your entrance door, at a top of about 4 toes from the bottom. Make it possible for the situation you select is degree and that there aren’t any obstructions, reminiscent of bushes or shrubs, that can block the view of the Ring Doorbell.
Tip 2: Use a powerful Wi-Fi sign.
The Ring Doorbell requires a powerful Wi-Fi sign to perform correctly. In case you have a weak Wi-Fi sign within the space the place you need to set up the Ring Doorbell, it’s possible you’ll want to make use of a Wi-Fi extender or booster to enhance the sign energy.
Tip 3: Arrange movement detection and notifications.
The Ring Doorbell has a built-in movement sensor that can be utilized to set off notifications in your smartphone. You may customise the movement detection settings to solely obtain notifications for sure kinds of movement, reminiscent of individuals or autos.
Tip 4: Join your Ring Doorbell to different sensible residence gadgets.
The Ring Doorbell could be related to different sensible residence gadgets, reminiscent of sensible lights and sensible locks. This lets you create automated actions, reminiscent of turning on the lights when somebody rings the doorbell or unlocking the door once you reply the doorbell out of your smartphone.
Closing Paragraph for Ideas: By following the following pointers, you will get essentially the most out of your new Ring Doorbell and luxuriate in all the advantages that it has to supply.
Now that you understand how to put in and use your Ring Doorbell, you may benefit from the peace of thoughts that comes with realizing which you can monitor your private home and reply the door from wherever.
Conclusion
Putting in a Ring Doorbell is a good way to enhance the safety of your private home and keep watch over your property. By following the steps on this information, you may simply set up your Ring Doorbell your self and begin having fun with all the advantages that it has to supply.
Abstract of Primary Factors:
- Flip off the ability to your doorbell earlier than you start set up.
- Take away your present doorbell.
- Set up the mounting bracket.
- Join the doorbell wires to the Ring Doorbell.
- Mount the Ring Doorbell to the mounting bracket.
- Degree and safe the Ring Doorbell.
- Restore energy to the doorbell.
- Take a look at the Ring Doorbell.
Closing Message: Along with your Ring Doorbell put in, now you can get pleasure from peace of thoughts realizing which you can monitor your private home and reply the door from wherever. You may as well use the Ring Doorbell to attach with different sensible residence gadgets and create automated actions to make your private home much more safe and handy.
